question about path signals
Moderator: OpenTTD Developers
question about path signals
Hello,
I am trying to understand how path signals work. I have made this test scenario (see in attachment).
- top train has two stations - Transfer <--> West
- bottom train has two stations - West <--> Halt
- current order of both trains is goto West
Question is, why both trains are waiting for free path? As far as I understood, each train should reserve highlighted (red & blue) piece of track and they should not interfere.
This only happens, when the middle trainstaion is connected from back side too (so it creates loop). If I remove the green highglighted connector, they don't wait for pree path and work normally. But the manual says, that trains should only reserve the path to the safe stopping point, which is the station. They should not care about what's after the station.
Can you help me uderstand this situation? Thanks
I am trying to understand how path signals work. I have made this test scenario (see in attachment).
- top train has two stations - Transfer <--> West
- bottom train has two stations - West <--> Halt
- current order of both trains is goto West
Question is, why both trains are waiting for free path? As far as I understood, each train should reserve highlighted (red & blue) piece of track and they should not interfere.
This only happens, when the middle trainstaion is connected from back side too (so it creates loop). If I remove the green highglighted connector, they don't wait for pree path and work normally. But the manual says, that trains should only reserve the path to the safe stopping point, which is the station. They should not care about what's after the station.
Can you help me uderstand this situation? Thanks
- Attachments
-
- OpenTTD_2020-10-26-16-42-37.jpg
- (1.36 MiB) Not downloaded yet
Re: question about path signals
Have a look, basically the tracks need to be sectioned.
- Attachments
-
- Tinnpool Transport, 1950-05-17.png
- (1.18 MiB) Not downloaded yet
Re: question about path signals
Thanks.
Althought have you any idea what happenned in my situation? (i would really like to have a full grasp of these path signals )
Althought have you any idea what happenned in my situation? (i would really like to have a full grasp of these path signals )
Re: question about path signals
Station is not safe stopping point, it is just stopping point. Safe stopping point == signal, depot. Blue train is reserving green loop in advance, if there are no signals, even if it would reverse on station later.
Re: question about path signals
thought that if station acts like a signal (because it stops the trains and forces them to find free path), it is also a safe point ... but since trains can enter station from both ways, it can't be safe .. that would make sense .. ok, thank you
-
- Route Supervisor
- Posts: 389
- Joined: 08 Nov 2019 23:54
Re: question about path signals
The situation is that the train reserves the path not only to the nearest station, but to the end of the orders list as far as it can. Only signals or the end of the track can interrupt searching of the path.
If you want to better understand how path signals work, there is a useful feature to show them.
In the case you showed pathfinder without any signals restrictions, he also tried to search for the rest of the route, i.e. back to the first station (orange line), and he did so, but could not let the train start because the road to the first station was already taken, by some train - in this case the same train. It was enough to put up a signal to break the search and let the train move. Interestingly, after stopping at the second station, pathfinder will search the paths again and send the train the same way it came (unless the option to prohibit U-turns at stations was not enabled).
If you want to better understand how path signals work, there is a useful feature to show them.
In the case you showed pathfinder without any signals restrictions, he also tried to search for the rest of the route, i.e. back to the first station (orange line), and he did so, but could not let the train start because the road to the first station was already taken, by some train - in this case the same train. It was enough to put up a signal to break the search and let the train move. Interestingly, after stopping at the second station, pathfinder will search the paths again and send the train the same way it came (unless the option to prohibit U-turns at stations was not enabled).
- Attachments
-
- reserved path.PNG
- (285.31 KiB) Not downloaded yet
I am sorry for may English. I know is bed.
Re: question about path signals
I think it has been explained by others but as I understand 'path' signnals they protect a path (section) of track and a train cannot enter that path (section ) if another train is on it or the train cannot find a path to the next signal without crashing.
Another screenshot, you will see a few trains on the crossing lines, they were allowed into this section because they could find a safe path to the next signal, if there is not a safe path the signals would not allow them onto that section (remain red)
I have included a save as an example, without any GRF's and three trains.
Another screenshot, you will see a few trains on the crossing lines, they were allowed into this section because they could find a safe path to the next signal, if there is not a safe path the signals would not allow them onto that section (remain red)
I have included a save as an example, without any GRF's and three trains.
- Attachments
-
- Custon Transport, 1951-01-18.sav
- (676.65 KiB) Downloaded 76 times
-
- Slenham Transport, 1970-02-01.png
- (1.83 MiB) Not downloaded yet
Re: question about path signals
thank you, it's much clearer now, I can continue testing I was thinking about some plugin that would highlight the track reservations, didn't think that it's already implemented in the game. That will help a lot
Who is online
Users browsing this forum: No registered users and 8 guests